|
User manual for Lectrosonics LMb Digital Hybrid Wireless Beltpack LMB-C1
- Manufacturer: Lectrosonics
- Basic description and contents of package
- Product classification: Pro Audio - Location Sound - Wireless Transmitters
- Safety instructions
- Startup and operation of the wireless transmitters
- Tips for setting up your Lectrosonics
- Settings and expert assistance
- Contact Lectrosonics service
- Troubleshooting
- Warranty information
- Price: 809 USD
|
We recommend checking out our discussion threads on the Lectrosonics LMb Digital Hybrid Wireless Beltpack LMB-C1,
which address similar problems with connecting and setting up Wireless Transmitters Lectrosonics.
|
User manual for the Lectrosonics LMb Digital Hybrid Wireless Beltpack LMB-C1
The user manual for the Lectrosonics LMb Digital Hybrid Wireless Beltpack LMB-C1 provides
necessary instructions for the proper use of the product Pro Audio - Location Sound - Wireless Transmitters.
The LMb from Lectrosonics is a digital hybrid wireless beltpack transmitter with 75 MHz tuning bandwidth and 50 mW RF power. When paired with a mic and receiver, it can be used to capture audio for applications such as broadcast TV, theater, houses of worship, live stage, and more.
|
If you own a Lectrosonics wireless transmitters and have a user manual in electronic form,
you can upload it to this website using the link on the right side of the screen.
You can upload and download the manual for the Lectrosonics LMb Digital Hybrid Wireless Beltpack LMB-C1 in the following formats:
- *.pdf, *.doc, *.txt, *.jpg - Other formats are unfortunately not supported.
|
Additional parameters of the Lectrosonics LMb Digital Hybrid Wireless Beltpack LMB-C1:
| Channel | C1 | | Frequency Range | 614.400 to 691.175 MHz | | Frequency Selection | Steps: Selectable 25 or 100 kHz | | RF Power Output | 50 mW | | Pilot Tone | 25 to 32 kHz, 5 kHz deviation (Digital Hybrid mode) | | Frequency Stability | ± 0.002% | | Deviation | ± 75 kHz max. (Digital Hybrid mode) | | Spurious Radiation | 60 dB below carrier | | Equivalent Input Noise | -120 dBV (A-weighted) | | Input Level | Nominal 2 mV to 300 mV, before limiting
Greater than 1 V maximum, with limiting | | Input Impedance | 2 kOhms | | Input Limiter | DSP controlled, dual envelope "soft" limiter with greater than 30 dB range | | Gain Control Range | 44 dB, digital control | | Modulation Indicators | Dual bicolor LEDs indicate modulation of -20, -10, 0 and +10 dB referenced to full modulation
LCD bar graph | | Frequency Response | 90 Hz to 20 kHz (+/-1 dB) | | Low Frequency Roll-Off | -12 dB/octave, 70 Hz | | THD | 0.2% (typical) | | SNR at Receiver Output | SmartNR: Off 103.5 (no limiting) 108.0 (with limiting)
Normal: 107.0 (no limiting) 111.5 (with limiting)
Full: 108.5 (no limiting) 113.0 (with limiting)
Note: The dual envelope "soft" limiter provides good handling of transients using variable attack and release time constants. Once activated, the limiter compresses 30+ dB of transmitter input range into 4.5 dB of receiver output range, thus reducing the measured figure for SNR without limiting by 4.5 dB | | Switch Controls | Top panel slide switch; programmable as power, mute, talkback or no (off) function
Side panel membrane switches with LCD interface for power on/off and all setup and configuration controls | | Audio Input Jack | 1x Switchcraft 5-pin locking (TA5F) | | Antenna | Galvanized steel, flexible wire | | Battery | 2x AA alkaline, lithium, NiMh rechargeable | | Battery Life | Alkaline: 4.5 hours
Duracell Quantum: 7 hours
Eneloop 2400 mAH NiMH: 8 hours | | Dimensions (L x W x H) | 3.2 x 2.4 x .8" (81 x 61 x 20 mm) | | Weight | 5 oz (141 g), including lithium AA batteries and wire belt clip | | Package Weight | 0.95 lb | | Box Dimensions (LxWxH) | 13.3 x 5.3 x 3.5" | |
The user manual for the Lectrosonics LMb Digital Hybrid Wireless Beltpack LMB-C1 can be downloaded in .pdf
format if it did not come with your new wireless transmitters, although the seller is
required to supply one. It is also quite common that customers throw out
the user manual with the box, or put the CD away somewhere and then can’t find it.
That’s why we and other Lectrosonics users keep a unique electronic library
for Lectrosonics wireless transmitterss,
where you can use our link to download the user manual for the Lectrosonics LMb Digital Hybrid Wireless Beltpack LMB-C1.
The user manual lists all of the functions of the Lectrosonics LMb Digital Hybrid Wireless Beltpack LMB-C1,
all the basic and advanced features and tells you how to use the wireless transmitters.
The manual also provides troubleshooting for common problems. Even greater
detail is provided by the service manual, which is not typically shipped with the product,
but which can often be downloaded from Lectrosonics service.
If you want to help expand our database, you can upload a link to this website
to download a user manual or service manual, ideally in .pdf format. These pages
are created by you – users of the Lectrosonics LMb Digital Hybrid Wireless Beltpack LMB-C1. User manuals are also
available on the Lectrosonics website under Pro Audio - Location Sound - Wireless Transmitters.
Question and answer discussion forum concerning user instructions and resolving problems with the Lectrosonics LMb Digital Hybrid Wireless Beltpack LMB-C1 - no comments have been made yet - be the first to add a comment
Post new comment/question/response regarding the Lectrosonics LMb Digital Hybrid Wireless Beltpack LMB-C1
|
|
|
|
|
