User manual MuxLab 16-Channel LongReach II Active CCTV Receiver Hub 500127

User manual for MuxLab 16-Channel LongReach II Active CCTV Receiver Hub 500127

Manufacturer: MuxLab

Basic description and contents of package

Product classification: Surveillance - Surveillance Video - Video Transmission - Signal Extenders

Safety instructions

Startup and operation of the signal extenders

Tips for setting up your MuxLab

Settings and expert assistance

Contact MuxLab service

Troubleshooting

Warranty information

Click to enlarge image

Video
Bandwidth	20 Hz to 8 MHz
Input	1.5 Vpp maximum, 100 ohms, balanced (RJ45)
Output	1.1 Vpp, ± 1 dB, 75 ohms, unbalanced (BNC)
Insertion Loss	-14 dB minimum for luma, -60 dB minimum for chroma Determined by Automatic Gain Control
Return Loss	>15 dB over the frequency range
Common Mode Rejection	>40 dB @ 3.85 MHz
Ground Loop Isolation	Up to +/-50 VDC
Auto Polarity Correction	Automatically adjusts for any polarity
Maximum Distance via Cat5e/6	NTSC: 5000' (1524 m) with passive CCTV balun at camera NTSC: 7000' (2133.6 m) with 500100/101 at camera Coax jumper cables must be less than 30' (9 m)
LED Diagnostics	Power, video sync
AGC (Automatic Gain Control)	Automatically adjusts for gain, sharpness, and luminosity Stabilization Time: Under 1 second

Remote Power
Wiring	Remote low voltage power supported via 2 or 3 twisted pairs A class II power supply is recommended
Maximum Distance	@ 24 VAC via three twisted pairs 2 VA: 1500' (457 m) 4 VA: 745' (227 m) 10 VA: 300' (91 m) 20 VA: 150' (46 m) Longer distances may be achieved @ 28 VAC Based on 10% voltage drop at camera
Maximum Current	2.5 A rms or DC

PTZ Control
Wiring	Remote 2-wire PTZ control supported via 1 twisted pair
Maximum Distance	Up to 4000' (1219.2 m) depending on the PTZ camera vendor
Maximum Input Voltage	48 V (AC RMS/DC)
Maximum Current Rating	2 A (AC RMS/DC). No fuse

Others
Signal	CCTV composite baseband video; NTSC, PAL, SECAM
Devices	CCTV cameras, monitors, DVR, switchers, IP encoders, and other CCTV equipment
Transmission	Transparent to the user

Mechanical & Environmental
UTP	24 gauge or lower solid copper twisted pair wire Impedance: 100 ohms at 1 MHz Maximum Capacitance: 20 pf/foot Attenuation: 6.6 dB/1000' (304.8 m) at 1 MHz
Cable - Coax	Impedance: 75 ohms at 1 MHz (RG59/U)
Switch	Select between Power-Thru (500024/500029) and Pass-Thru (500022) mode
Connectors	16 x BNC-F Remote Power: 16 x 2-pole screw terminal block PTZ: 16 x 2-pole screw terminal block Cat5e/6 Link: 16 x RJ45S Power connector Ground screw terminal
Compatible Baluns	500000, 500000R, 500009, 500022, 500024, 500100/10
Power Supply	5 VDC / 2.6 A maximum Floating: +/- 20% Interchangeable blades 1.53 A maximum
Protection	± 2.5 V on the video line ± 48 V on the power and control lines
Power Surge Protection	Above 34 VAC RMS or +/- 48 VDC
Fuse Protection	Auto-resettable fuse on 5 VDC input and Power A (+) upon power cycling
Temperature	Operating: 32 to 131°F (0 to 55°C) Storage: -4 to 185°F (-20 to 85°C)
Humidity	Up to 95%
Enclosure	Aluminum
Regulatory	FCC and CE
Dimensions	16.9 x 5.0 x 1.6" (42.9 x 12.9 x 4.2 cm)
Weight	4.6 lb (2.1 kg)

PDF-MANUALS.com \| User manual here!
	User manual MuxLab 16-Channel LongReach II Active CCTV Receiver Hub 500127 Operating instructions and pdf manual for use - MuxLab 16-Channel LongReach II Active CCTV Receiver Hub 500127 User manual, User manual MuxLab 16-Channel LongReach II Active CCTV Receiver Hub 500127, MuxLab, 16-Channel, LongReach, II, Active, CCTV,

User manual for MuxLab 16-Channel LongReach II Active CCTV Receiver Hub 500127