User manual Radial Engineering X-Amp 500 Reamper Module R700 0130
Operating instructions and pdf manual for use - Radial Engineering X-Amp 500 Reamper Module R700 0130 User manual, User manual Radial Engineering X-Amp 500 Reamper Module R700 0130, Radial, Engineering, X-Amp, 500, Reamper, Module, R700, 0130,
User manual for Radial Engineering X-Amp 500 Reamper Module R700 0130
Manufacturer: Radial Engineering
Basic description and contents of package
Product classification: Pro Audio - Recording - Direct Boxes
Safety instructions
Startup and operation of the direct boxes
Tips for setting up your Radial Engineering
Settings and expert assistance
Contact Radial Engineering service
Troubleshooting
Warranty information
Price: 300 USD
We recommend checking out our discussion threads on the Radial Engineering X-Amp 500 Reamper Module R700 0130,
which address similar problems with connecting and setting up Direct Boxes Radial Engineering.
User manual for the Radial Engineering X-Amp 500 Reamper Module R700 0130
The user manual for the Radial Engineering X-Amp 500 Reamper Module R700 0130 provides
necessary instructions for the proper use of the product Pro Audio - Recording - Direct Boxes.
The Radial Engineering X-Amp 500 Reamper Module is part of the 500 Series and lets you take a pre-recorded guitar track and send it back to amplifiers and effects so that you can tailor the sound to suit. Reamping allows the guitarist to only concentrate on the performance while recording. Working out specific sounds and optimal microphone placement can be done later. This eliminates hours of tiresome repetition, while allowing the producer to adjust the character of the track as the production evolves.
The X-Amp is easy to use with its plug-n-play feature. The design begins with an XLR balanced line level input located on the 500 series rear panel that feeds the X-Amp. To ensure high fidelity, a 100% discrete class-A circuitry is employed. The X-Amp unbalances and buffers the pre-recorded signal where it then feeds two transformer-isolated hi-Z guitar level outputs. The ¼" jacks are front-mounted for desk-top convenience and equipped with ground lifts to help eliminate hum and buzz caused by ground loops. Independent level controls enable you to adjust the drive going to each amp for optimal tone. In case one of the amps are out of phase, then depressing the 180º quickly brings both in line.
Separate output controls make it easy to set the guitar amplifiers to a suitable level from the control room. A 180° polarity reverse assures that both the amplifiers will play in phase. In use, the X-Amp enables the user to take a pre-recorded track and send it simultaneously to two amplifiers. This makes it easy to optimize the track to best suit the recording. The guitar cables can be extended to 50’ (15m) without noise. Reamping is often used on guitars, bass, and keyboards to create effects, thicken the tone, or simply replace poorly recorded tracks.
If you own a Radial Engineering direct boxes and have a user manual in electronic form,
you can upload it to this website using the link on the right side of the screen.
You can upload and download the manual for the Radial Engineering X-Amp 500 Reamper Module R700 0130 in the following formats:
*.pdf, *.doc, *.txt, *.jpg - Other formats are unfortunately not supported.
Additional parameters of the Radial Engineering X-Amp 500 Reamper Module R700 0130:
Specifications
Circuit Type
Class-A discrete, transformer-coupled
Power Requirement
40 mA, ± 16 VDC
Frequency Response
20 Hz to 20 kHz (adjusted for guitar signals -5 dB @ 20 kHz) - 100 K Load
Voltage Gain
XLR Input to XLR Output: 0 ± 0.5 dB Omniport to XLR Output: -3 ± 0.5 dB XLR Input to ¼" Outputs: -0.6 ± 0.5 dB
THD + N
XLR Input to XLR Output: <0.002% @ 0 dBu (20 Hz to 20 kHz) Omniport to XLR Output: <0.002% @ 0 dBu (20 Hz to 20 kHz) XLR Input to ¼" Outputs: <0.006% @ 0 dBu (1 kHz)
Noise
XLR Input to XLR Output: -114 dB below 0 dBu Omniport to XLR Output: -95 dB below 0 dBu XLR Input to ¼" Outputs: -98 dB below 0 dBu
Intermodulation Distortion
XLR Input to XLR Output: <0.04% @ 0 dBu input Omniport to XLR Output: <0.005% @ 0 dBu input XLR Input to ¼" Outputs: <0.027% @ 0 dBu input
Maximum Input
XLR Input to XLR Output: 26 dBu Omniport to XLR Output: 20 dBu XLR Input to ¼" Outputs: 19 dBu
The user manual for the Radial Engineering X-Amp 500 Reamper Module R700 0130 can be downloaded in .pdf
format if it did not come with your new direct boxes, although the seller is
required to supply one. It is also quite common that customers throw out
the user manual with the box, or put the CD away somewhere and then can’t find it.
That’s why we and other Radial Engineering users keep a unique electronic library
for Radial Engineering direct boxess,
where you can use our link to download the user manual for the Radial Engineering X-Amp 500 Reamper Module R700 0130.
The user manual lists all of the functions of the Radial Engineering X-Amp 500 Reamper Module R700 0130,
all the basic and advanced features and tells you how to use the direct boxes.
The manual also provides troubleshooting for common problems. Even greater
detail is provided by the service manual, which is not typically shipped with the product,
but which can often be downloaded from Radial Engineering service.
If you want to help expand our database, you can upload a link to this website
to download a user manual or service manual, ideally in .pdf format. These pages
are created by you – users of the Radial Engineering X-Amp 500 Reamper Module R700 0130. User manuals are also
available on the Radial Engineering website under Pro Audio - Recording - Direct Boxes.
Question and answer discussion forum concerning user instructions and resolving problems with the Radial Engineering X-Amp 500 Reamper Module R700 0130 - no comments have been made yet - be the first to add a comment