|
User manual for Rane HAL3s Multiprocessor HAL3S
- Manufacturer: Rane
- Basic description and contents of package
- Product classification: Pro Audio - Installation Sound - System Processors
- Safety instructions
- Startup and operation of the system processors
- Tips for setting up your Rane
- Settings and expert assistance
- Contact Rane service
- Troubleshooting
- Warranty information
|
We recommend checking out our discussion threads on the Rane HAL3s Multiprocessor HAL3S,
which address similar problems with connecting and setting up System Processors Rane.
|
User manual for the Rane HAL3s Multiprocessor HAL3S
The user manual for the Rane HAL3s Multiprocessor HAL3S provides
necessary instructions for the proper use of the product Pro Audio - Installation Sound - System Processors.
The HAL3s from Rane is a Multiprocessor which supports 6 input by 10 output audio with 2 input x 6 output balanced analog connections, and another 4 input x 4 outputs digitally through RADs (remote digital devices). The two analog inputs are Line/Line-Plus/Mic/Mic + 48V phantom power. In addition to supporting balanced line and microphone inputs, this configuration allows a stereo pair connection to an input, converting to a single L+R mono signal.
Two DR (digital remote) ports provide support for preset recall, level control and select functions using a DR1, DR2, or DR3. If more logic inputs and outputs are needed for ports, switches or external indicators (DR4 or DR5) may be added. DRs can be operated from a RAD port, so up to four DRs can plug into a HAL3s when RADs aren't needed.
|
If you own a Rane system processors and have a user manual in electronic form,
you can upload it to this website using the link on the right side of the screen.
You can upload and download the manual for the Rane HAL3s Multiprocessor HAL3S in the following formats:
- *.pdf, *.doc, *.txt, *.jpg - Other formats are unfortunately not supported.
|
Additional parameters of the Rane HAL3s Multiprocessor HAL3S:
| Analog I/O | 2 x mic / line / line-plus inputs
6 x line outputs | | Connectors | 4 x 6-pin, 5 mm pitch, Euroblock | | Codec | 24 bit, 48 kHz | | Input Impedance | 2.9 kΩ, 1% each leg to ground | | Isolation Between Channels | > 100 dB typical 20 - 20k Hz, unity gain, channel-to-channel | | CMRR | 55 dB, minimum 1 kHz | | Microphone Inputs | Dynamic Microphone Mode:
Gain: +30 dB to +50 dB
THD + N: < 0.005%, typical 20 - 20 kHz, +4 dBu out, 0 dB digital gain
Equivalent Input Noise: -120 dBu, typical 20 - 20 kHz, 150 Ω source, 30 dB gain
Maximum Input: -18 dBV (125 mVrms), typ 1 kHz, < 0.01% THD+N
Frequency Response: 20 - 20 kHz, +0.0 / -0.3 dB +4 dBu out, 100k Ω load, Microphone Input to Output
Condenser Microphone Mode:
Gain: +18 dB to +38 dB
Phantom Power: +48 VDC 10 mA max per input
THD + N: < 0.005%, typical 20 - 20 kHz, +4 dBu out, 0 dB digital gain
Equivalent Input Noise: -110 dBu, typ 20 - 20 kHz, 150 Ω source, 18 dB gain
Maximum Input: -6 dBV (500 mVrms), typ 1 kHz, < 0.01% THD+N
Frequency Response: 20 - 20 kHz, +0.0 / -0.3 dB +4 dBu out, 100k Ω load, Mic Input to Output | | Line Inputs | Line + Mode:
Gain: 0 dB to +20 dB
THD + N: < 0.007 % typical 20 - 20 kHz, +4 dBu out, 0 dB digital gain
Maximum Input: +14 dBu typical 1 kHz, < 0.01% THD+N, each leg
Frequency Response: 20 - 20 kHz, +0.0 / -0.3 dB, +4 dBu out, 100k Ω load, Line-plus Input to Output
Dynamic Range (In to Out): 108 dB, maximum re +20 dBu, 20 kHz BW, A weighted, Rs = 50 Ω
Line Mode:
Gain: 0 d
THD + N: < 0.005 % typical 20 - 20 kHz, +4 dBu out, 0 dB digital gain
Maximum Input: +14 dBu typical 1 kHz, < 0.01% THD+N
Frequency Response: 20 - 20 kHz, +0.0 / -0.3 dB, +4 dBu out, 100k Ω load, Line Input to Output
Dynamic Range (In to Out): 108 dB, maximum re +20 dBu, 20 kHz BW, A weighted, Rs = 50 Ω | | Outputs | Impedance: 200 Ω, 1% each leg
Maximum Output: +20.0 / +15.5 dBu typ 1 kHz, 100 kΩ / 600 Ω load | | Indicators | Signal: -50 dBFS, green LED, peak-reading
Overload: -0.5 dBFS, red LED, peak-reading | | Propagation Delay | RAD In to RAD Out: 1.71 ms
RAD In to Analog Out: 1.85 ms
Analog In to RAD Out: 2.25 ms
Analog In to Analog Out: 2.39 ms | | DSP | Processing Power: 2400 MIPS, maximum 1 DSP @ 300 MHz with up to 8 instructions / cycle
Word Length: 32 / 64-bit Floating Point
Delay Memory: 20 seconds maximum | | Computer Interface | Type: Ethernet 1000 base-T
Cable: Shielded CAT 5e or better
Length: 300' (100 m) maximum | | Ports | RAD Port:
Audio Channels: 2 in x 2 out, control channel, 24-bit, 48 kHz
Power: 24 VDC @ 100 mA per port
Length: 500' (152 m)
DR Ports:
Power: 24 VDC @ 50 mA per port
Length: 1000' (300 m) | | Logic Input | Connector: Mini Euroblock, 6-pin, 3.81 mm pitch, black
Internal Pull-Up: 51.1 kΩ, 5.0 V, protected to +24 V, reverse polarity protected
Vin High: > 2.2 V
Vin Low: < 0.7 V | | Wiring | Class 2 | | Power Requirements | 100 to 240 VAC, 50 / 60 Hz, 20 W max | | Ambient Temperature | 104° F (40° C) | | Approvals and Compliance | CE, FCC, CCSAUS | | Dimensions (H x W x D) | 1.7 x 19.0" x 8.25" (4.4 x 48.3 x 20.9 cm) | | Weight | 4.75 lb (2.2 kg) | | Package Weight | 8.75 lb | | Box Dimensions (LxWxH) | 20.2 x 13.7 x 4.3" | |
The user manual for the Rane HAL3s Multiprocessor HAL3S can be downloaded in .pdf
format if it did not come with your new system processors, although the seller is
required to supply one. It is also quite common that customers throw out
the user manual with the box, or put the CD away somewhere and then can’t find it.
That’s why we and other Rane users keep a unique electronic library
for Rane system processorss,
where you can use our link to download the user manual for the Rane HAL3s Multiprocessor HAL3S.
The user manual lists all of the functions of the Rane HAL3s Multiprocessor HAL3S,
all the basic and advanced features and tells you how to use the system processors.
The manual also provides troubleshooting for common problems. Even greater
detail is provided by the service manual, which is not typically shipped with the product,
but which can often be downloaded from Rane service.
If you want to help expand our database, you can upload a link to this website
to download a user manual or service manual, ideally in .pdf format. These pages
are created by you – users of the Rane HAL3s Multiprocessor HAL3S. User manuals are also
available on the Rane website under Pro Audio - Installation Sound - System Processors.
Question and answer discussion forum concerning user instructions and resolving problems with the Rane HAL3s Multiprocessor HAL3S - no comments have been made yet - be the first to add a comment
Post new comment/question/response regarding the Rane HAL3s Multiprocessor HAL3S
|
|
|
|
|
