|
User manual for Toa Electronics DP-SP3 2-In/6-Out Digital Speaker DP-SP3 CU
- Manufacturer: Toa Electronics
- Basic description and contents of package
- Product classification: Pro Audio - Installation Sound - System Processors
- Safety instructions
- Startup and operation of the system processors
- Tips for setting up your Toa Electronics
- Settings and expert assistance
- Contact Toa Electronics service
- Troubleshooting
- Warranty information
|
We recommend checking out our discussion threads on the Toa Electronics DP-SP3 2-In/6-Out Digital Speaker DP-SP3 CU,
which address similar problems with connecting and setting up System Processors Toa Electronics.
|
User manual for the Toa Electronics DP-SP3 2-In/6-Out Digital Speaker DP-SP3 CU
The user manual for the Toa Electronics DP-SP3 2-In/6-Out Digital Speaker DP-SP3 CU provides
necessary instructions for the proper use of the product Pro Audio - Installation Sound - System Processors.
The TOA Electronics DP-SP3 2-In/6-Out Digital Speaker System Processor is a 1RU rackmountable signal processor designed for 3-way multi-amp systems in venues, banquet halls, houses of worships, restaurants, gymnasiums, and more. It features an equalizer, crossover, digital matrix, compressor, and delay. It also features an input pad, an analog output attenuator, an output mute control, front panel LED metering, 16 re-callable presets, an EQ characteristic library for optimization of TOA speakers, and contact input terminals. The unit includes a CAT5 connection for software control from a PC over a local area network. The unit features 24-bit 96 kHz sampling resolution, 10 filters on each input, and 12 filters on each output for any combination of high/low shelving filters, all-pass, notch filters, CD horn equalizers, high/low pass filters, or parametric equalizer. It includes four contact input terminals for output volume control, output muting, and memory recall. The unit comes with a power cord, eight 3P removable terminal plugs, one 5P removable terminal plug, and a CD-ROM containing software for Windows.
|
If you own a Toa Electronics system processors and have a user manual in electronic form,
you can upload it to this website using the link on the right side of the screen.
You can upload and download the manual for the Toa Electronics DP-SP3 2-In/6-Out Digital Speaker DP-SP3 CU in the following formats:
- *.pdf, *.doc, *.txt, *.jpg - Other formats are unfortunately not supported.
|
Additional parameters of the Toa Electronics DP-SP3 2-In/6-Out Digital Speaker DP-SP3 CU:
Frequency Response | 20 to 20,000 Hz ±1 dB | Sampling Frequency | 96 kHz | Dynamic Range | 110 dB or more | Distortion | 0.03% or less 1 kHz, +4 dB+ input/output, 20 to 20,000 Hz BPF | Crosstalk | -80 dB or less, 1 kHz | Input | 2x channels, +4 dB+ (max +24 dB+), 10 kΩ, electronically-balanced, removable terminal block (3P) | Output | 6x channels, +4 dB+ (max +24 dB+), applicable load 600 Ω or more, electronically-balanced, removable terminal block (3P) | A/D Converter | 24-bits | D/A Converter | 24-bits | Preset | 16 | Equalizer | Parametric Equalizer: 20 to 20,000 Hz: ±15 dB, Q: 0.267 to 69.249 Filter: High-Pass Filter: 20 to 20,000 Hz: 6 dB/oct, 12 dB/oct Low-Pass Filter: 20 to 20,000 Hz: 6 dB/oct, 12 dB/oct Notch Filter: 20 to 20,000 Hz: Q: 8.651 to 69.249 All-Pass Filter: 20 to 20,000 Hz: Q: 0.267 to 69.249 High-Shelving Filter: 5 to 20,000 Hz: ±15 dB Low-Shelving Filter: 20 to 500 Hz: ±15 dB Horn Equalizer: 20 kHz, 0 to 18 dB in 0.5 dB steps | Crossover | 2 ways, 3 ways, 4 ways Crossover Filter: 20 to 20,000 Hz, 6 dB/oct, 12 dB/oct, 18 dB/oct, 24 dB/oct -15 to +12 dB, polarity switchable Delay: 0 to 170.656 ms in 0.01 ms steps | Compressor | Threshold: -20 to +20 dB in 1 dB steps Ratio: 1:1, 1.1:1, 1.2:1, 1.3:1, 1.5:1, 1.7:1, 2:1, 2.3:1, 2.6:1, 3:1, 4:1, 7:1, 8:1, 10:1, 12:1, 20:1, ∞:1 Attack time: 0.2 ms to 5 s Release time: 10 ms to 5 s | Delay | 0 to 682.656 ms in 0.01 ms steps | Matrix Type | 2 x 6 | Crosspoint Mixing Modes | -∞ to 0 dB in 1 dB steps | Function | Input PAD (-14 dB) control, analog output attenuator (-∞ to 0 dB in 1 dB steps) control, EQ characteristic library for TOA speakers, input/output level indicator (4-point LED indicator), output MUTE switch x6 | Contact | Input: 4 channels, open voltage: 5 VDC, short-circuit current: 5 mA, removable terminal block (5 P) Control Function: Preset memory selection, volume control, and mute | Network | Network 1/F: 1 channel of 10BASE-T/100BASE-TX (auto-negotiation) RJ45 connector, connection via switching hub Network Protocol: TCP/IP Connection Cable: Shielded Cat 5 or higher twisted pair cable for LAN (Cat. 5-STP or better) Maximum Cable Length: 100 m (109.36 yd) (between DP-SP3 and switching hub) | Operating Temperature | 32 to 104°F (0 to +40° C) | Operating Humidity | 90% RHS (no condensation) | Finish | Panel: Aluminum, hairline, back Case: Surface-treated steel plate | Power Source | 100 to 120 VAC at 60 Hz | Power Consumption | 25 W | Requirements | CPU: Pentium 4, 1.0 GHz or faster Memory: Windows XP - 512 MB or more, other OS - 1.0 GB or more Display: 1024 x 768 resolution or higher Free Hard Disk Space: 16 MB or more, however 600 MB or more is required for the 32-bit version or 1.5 GB or more for 64-bit version when *.NET framework* is not yet installed
Optical Drive: CD-ROM drive Network Adapter: 10BASE-T or faster connection
Windows XP Service Pack 3 or later, Windows Vista (32/64-bit) Service Pack 1 or later, Windows 7 (32/64-bit)
Required Component: .NET Framework 4 Client Profile | Dimensions (W x H x D) | 18.98 x 1.73 x 11.38" (482 x 44 x 289 mm) | Weight | 6.83 lb (3.10 kg) | Package Weight | 10.0 lb | Box Dimensions (LxWxH) | 22.441 x 18.819 x 3.543" | |
The user manual for the Toa Electronics DP-SP3 2-In/6-Out Digital Speaker DP-SP3 CU can be downloaded in .pdf
format if it did not come with your new system processors, although the seller is
required to supply one. It is also quite common that customers throw out
the user manual with the box, or put the CD away somewhere and then can’t find it.
That’s why we and other Toa Electronics users keep a unique electronic library
for Toa Electronics system processorss,
where you can use our link to download the user manual for the Toa Electronics DP-SP3 2-In/6-Out Digital Speaker DP-SP3 CU.
The user manual lists all of the functions of the Toa Electronics DP-SP3 2-In/6-Out Digital Speaker DP-SP3 CU,
all the basic and advanced features and tells you how to use the system processors.
The manual also provides troubleshooting for common problems. Even greater
detail is provided by the service manual, which is not typically shipped with the product,
but which can often be downloaded from Toa Electronics service.
If you want to help expand our database, you can upload a link to this website
to download a user manual or service manual, ideally in .pdf format. These pages
are created by you – users of the Toa Electronics DP-SP3 2-In/6-Out Digital Speaker DP-SP3 CU. User manuals are also
available on the Toa Electronics website under Pro Audio - Installation Sound - System Processors.
Question and answer discussion forum concerning user instructions and resolving problems with the Toa Electronics DP-SP3 2-In/6-Out Digital Speaker DP-SP3 CU - no comments have been made yet - be the first to add a comment
Post new comment/question/response regarding the Toa Electronics DP-SP3 2-In/6-Out Digital Speaker DP-SP3 CU
|
|
|
|
|