|
User manual for Metric Halo ULN-8 000-50000
- Manufacturer: Metric Halo
- Basic description and contents of package
- Product classification: Pro Audio - Computer Audio - Audio Interfaces & Systems
- Safety instructions
- Startup and operation of the audio interfaces & systems
- Tips for setting up your Metric Halo
- Settings and expert assistance
- Contact Metric Halo service
- Troubleshooting
- Warranty information
|
We recommend checking out our discussion threads on the Metric Halo ULN-8 000-50000,
which address similar problems with connecting and setting up Audio Interfaces & Systems Metric Halo.
|
User manual for the Metric Halo ULN-8 000-50000
The user manual for the Metric Halo ULN-8 000-50000 provides
necessary instructions for the proper use of the product Pro Audio - Computer Audio - Audio Interfaces & Systems.
The ULN-8 from Metric Halo is an extremely high-quality digital audio interface with on-board DSP processing for Apple computers. It can be used to record audio in the field or in the studio, and it packs a lot of power for mixing and mastering in stereo and multiple surround sound formats, including 7.1. It offers the utmost in sound quality, while remaining ultra-portable, easy to use, and unwaveringly powerful.
|
If you own a Metric Halo audio interfaces & systems and have a user manual in electronic form,
you can upload it to this website using the link on the right side of the screen.
You can upload and download the manual for the Metric Halo ULN-8 000-50000 in the following formats:
- *.pdf, *.doc, *.txt, *.jpg - Other formats are unfortunately not supported.
|
Additional parameters of the Metric Halo ULN-8 000-50000:
| Rails | Preamp Rails: +/- 15.8 Volts
Analog Rails (low power): +/- 9.9 Volts
Analog Rails (high power): +/- 12.6 Volts | | Phantom Power | 48 +/- 0.1 Volts
Max Phantom Current Per Mic: 10 ma | | Maximum Level | Maximum I/O Levels (Balanced) Peak Line Output @ 0 dBFS (no jumper/low power): +18.5 dBu
Peak Line Output @ 0 dBFS (output jumper/low power): +22.0 dBu
Peak Line Output @ 0 dBFS (output jumper/high power): +24.5 dBu
Analog Send Max Output: +21.5 dBu
Mic Pre Max Input: +20 dBu
Line In Max Input: +24.5 dBu
Output Impedance: 5 Ohms | | Monitoring | Nominal FS output (Balanced) Output Jumper Off: -19.0 dBu
Nominal FS output (Balanced) Output Jumper On: -12.0 dBu
Maximum Output: Same as Line
Gain Range: -96 dB to +30 dB
Gain Precision: +/- 0.05 dB
Gain Step: 0.5 dB | | Panel Microphone Preamp | Mic Pre Input + ADC Input Impedance: 3.3 kOhm
Dynamic Range (-60 dB, flat 0-22.05 kHz, typ): 115 dB
Dynamic Range (-60 dB, A-weighted, typ): 118 dB
Noise Floor (flat 0-22.05 kHz, typ): 115 dB
Noise Floor (A-weighted, typ): 117.9 dB
Gain Range: -22 dB to +91.5 dB
Gain Precision: +/- 0.05 dB
Gain Step: 0.05 dB
THD D/A/A/D loop @ -12 dBFS: 0.0007 %
THD D/A/A/D loop @ -12 dBFS +12 dB Gain: 0.0015 %
THD D/A/A/D loop @ -0 dBFS: 0.0023 %
Crosstalk @ 1kHz: -110 dB
IMD 1k component (19 kHz/20kHz @ +8dBu): -104 dBu
EIN @ 60 dB Gain (150 Ohm Source Impedance): -130.50 dBu
EIN @ 60 dB Gain (0 Ohm Source Impedance): -133.25 dBu
Analog Send Calibration (ADC = 0 dBFS): +21.5 dBu
Phantom Power (Switchable Per Channel): +48 Volts Mic Pre + ADC Frequency Response +0/-0.1dB @ fs = 44100 Hz: 8.9 Hz - 20.5 kHz
+0/-1.0dB @ fs = 44100 Hz: 2.9 Hz - 21.0 kHz
+0/-0.1dB @ fs = 96000 Hz: 8.9 Hz - 43.9 kHz
+0/-1.0dB @ fs = 96000 Hz: 2.9 Hz - 45.4 kHz
+0/-0.1dB @ fs = 192000 Hz: 8.9 Hz - 42.1 kHz
+0/-1.0dB @ fs = 192000 Hz: 2.9 Hz - 64.7 kHz
5 degree low-end in-channel phase deviation point: 20.0 Hz
Interchannel phase 0 Hz - 20 kHz: < +/- 0.05 degrees
Crosstalk from SMPTE Input: < -142 dB | | Lining | Line Input + ADC Input Impedance: 10 kOhm
Dynamic Range (-60 dB, flat 0-22.05 kHz, typ): 115 dB
Dynamic Range (-60 dB, A-weighted, typ): 118 dB
Noise Floor (flat 0-22.05 kHz, typ): 115 dB
Noise Floor (A-weighted, typ): 117.9 dB
THD D/A/A/D loop @ -12 dBFS: 0.0005 %
THD D/A/A/D loop @ -0 dBFS: 0.0015 %
Crosstalk @ 1 kHz: -127 dB
IMD 1k component (19 kHz/20kHz @ +8dBu): -104 dBu
Gain Range: -12 dB to +31.5 dB
Gain Precision: +/- 0.05 dB
Gain Step: 0.5 dB Line Input + ADC Frequency Response +0/-0.1dB @ fs = 44100 Hz: 5.7 Hz - 20.5 kHz
+0/-1.0dB @ fs = 44100 Hz: 1.8 Hz - 21.0 kHz
+0/-0.1dB @ fs = 96000 Hz: 5.7 Hz - 43.9 kHz
+0/-1.0dB @ fs = 96000 Hz: 1.8 Hz - 45.4 kHz
+0/-0.1dB @ fs = 192000 Hz: 5.7 Hz - 42.1 kHz
+0/-1.0dB @ fs = 192000 Hz: 1.8 Hz - 64.7 kHz
5 degree low-end in-channel phase deviation point: 10.7 Hz
Interchannel phase 0 Hz - 20 kHz: < +/- 0.05 degrees
Crosstalk from SMPTE Input: < -142.dB | | Audio Processing | Input Processing: M/S Decode
Parametric EQ
Dynamics
Limiting
Character
Transient Control
Reverb
Delay
Nearly Infinite Combinations via +DSP Output Processing: M/S Decode
Parametric EQ
Dynamics
Limiting
Character
Transient Control
Reverb
Dither
Mix Foldown
Signal Generation
Nearly Infinite Combinations via +DSP | | Rear Panel | MIDI Connectors (In and Out): 5-Pin DIN
SMPTE Connectors (In and Out): Balanced TRS
Word Clock Connectors (In and Out): 75 Ohm BNC
AES Connector (8 Channels In and Out): DB-25
AES Connector Pinout: Tascam/Digidesign Digital
Mic Input Connector (8 Channels): DB-25
Mic Input Connector Pinout: Tascam/Digidesign Analog
Line Input Connector (8 Channels): DB-25
Line Input Connector Pinout: Tascam/Digidesign Analog
Send Output Connector (8 Channels): DB-25
Send Output Connector Pinout: Tascam/Digidesign Analog
Line/Monitor Output Connector (8 Channels): DB-25
Line/Monitor Output Pinout: Tascam/Digidesign Analog
Line/Monitor Mult Output Connectors (Analog 1/2): TRS Balanced
FireWire Connectors (2): 1394a 6-Pin
Power (Unswitched): 2.1mm Coaxial
Power (Switched): 4-Pin XLR
Security Slot: Kensington | | Power | Voltage: 14v - 28v
Power: 32 Watts
FireWire Bus Powerable: No
Passes FireWire Bus Power: Yes
Supplies FireWire Bus Power: No
External Supply (Input): 100-240 VAC
External Supply (Max Input Current): 1.2 A
External Supply (Output): 24 VDC
External Supply (Max Output Current): 2.0 A
External Supply Connector: 4-Pin XLR | | Dimensions | 17 x 13 x 1.72" (432 x 330 x 44 mm) | | Weight | 6 lbs (2.7 kg) | | Package Weight | 10.6 lb | | Box Dimensions (LxWxH) | 19.5 x 15.9 x 7.0" | |
The user manual for the Metric Halo ULN-8 000-50000 can be downloaded in .pdf
format if it did not come with your new audio interfaces & systems, although the seller is
required to supply one. It is also quite common that customers throw out
the user manual with the box, or put the CD away somewhere and then can’t find it.
That’s why we and other Metric Halo users keep a unique electronic library
for Metric Halo audio interfaces & systemss,
where you can use our link to download the user manual for the Metric Halo ULN-8 000-50000.
The user manual lists all of the functions of the Metric Halo ULN-8 000-50000,
all the basic and advanced features and tells you how to use the audio interfaces & systems.
The manual also provides troubleshooting for common problems. Even greater
detail is provided by the service manual, which is not typically shipped with the product,
but which can often be downloaded from Metric Halo service.
If you want to help expand our database, you can upload a link to this website
to download a user manual or service manual, ideally in .pdf format. These pages
are created by you – users of the Metric Halo ULN-8 000-50000. User manuals are also
available on the Metric Halo website under Pro Audio - Computer Audio - Audio Interfaces & Systems.
Question and answer discussion forum concerning user instructions and resolving problems with the Metric Halo ULN-8 000-50000 - no comments have been made yet - be the first to add a comment
Post new comment/question/response regarding the Metric Halo ULN-8 000-50000
|
|
|
|
|
