User manual QSC WL2102 WideLine-10 Line Array Speaker System WL2102-W-BK
Operating instructions and pdf manual for use - QSC WL2102 WideLine-10 Line Array Speaker System WL2102-W-BK User manual, User manual QSC WL2102 WideLine-10 Line Array Speaker System WL2102-W-BK, QSC, WL2102, WideLine-10, Line, Array, Speaker, Syst
User manual for QSC WL2102 WideLine-10 Line Array Speaker System WL2102-W-BK
Basic description and contents of package
Product classification: Pro Audio - Live Sound - PA Speakers
Startup and operation of the pa speakers
Tips for setting up your QSC
Settings and expert assistance
Contact QSC service
Click to enlarge image
We recommend checking out our discussion threads on the QSC WL2102 WideLine-10 Line Array Speaker System WL2102-W-BK,
which address similar problems with connecting and setting up PA Speakers QSC.
User manual for the QSC WL2102 WideLine-10 Line Array Speaker System WL2102-W-BK
The user manual for the QSC WL2102 WideLine-10 Line Array Speaker System WL2102-W-BK provides
necessary instructions for the proper use of the product Pro Audio - Live Sound - PA Speakers.
The WL2102 WideLine-10 Line Array Speaker System from QSC is a full range line array loudspeaker system designed for use in a wide variety of venues. The WideLine-10 features a wide 140° horizontal coverage pattern. It is a three transducer system and can be operated in either bi-amplified or tri-amplified modes. Both 10" diameter low frequency transducers are used to cover the lowest frequency range. One driver covers only low frequencies while the range of the other extends through the mid frequencies to the mid/high crossover point. The use of a single midrange transducer allows the horizontal coverage pattern to remain wide and to assure smooth response both on and off axis at the transition to the diffraction slot loaded high frequency section. Bi-amplification uses passive elements to affect the required frequency response shading of the low-frequency drivers and offers reduced amplifier channel counts and simplified wiring. Tri-amplification allows the required low-frequency shading to be controlled with greater precision via active electronics and is recommended where maximum output and high sound quality are required.
The WideLine-10's 16 ohm per transducer low-frequency impedance optimizes allocation of amplifier channels. In biamp mode the LF/ MF sections of up to four enclosures can be powered by one amplifier channel operating into a 2-ohm load. In tri-amp mode the LF and MF sections of up to eight enclosures can be powered by a single two channel amplifier. The high-frequency section consists of a 1.4" exit, 3" 16 ohm, neodymium compression driver, mounted on a proprietary multiple aperture diffraction slot waveguide. The mechanical design allows composite and plywood enclosures to be arrayed together. WideLine-10 features a unique 3-point suspension system allowing construction of arrays of up to 24 enclosures (5:1 design factor). A 12-enclosure hang will maintain a 10:1 design factor. Vertical splay angles between adjacent enclosures are adjustable in one degree increments from 0 to 10°.
All hardware required to construct an array is permanently attached to the enclosure. Two array frame models (sold separately) offer the user the flexibility to choose the right tool for the job. The AF2102, the larger of the two, can accommodate array sizes up 12 enclosures while maintaining a design factor of 10:1. The smaller AF2102-s does triple-duty; accommodating suspended arrays of up to six enclosures with a 10:1 design factor, acting as a base for ground-stacked arrays of up to six enclosures and as an attachment allowing WideLine-10s to be stacked atop QSC 215PCM and 215SB subwoofers.
If you own a QSC pa speakers and have a user manual in electronic form,
you can upload it to this website using the link on the right side of the screen.
You can upload and download the manual for the QSC WL2102 WideLine-10 Line Array Speaker System WL2102-W-BK in the following formats:
*.pdf, *.doc, *.txt, *.jpg - Other formats are unfortunately not supported.
Additional parameters of the QSC WL2102 WideLine-10 Line Array Speaker System WL2102-W-BK:
HF: 80 W (2 hours, AES1984-2 method, 1 to 10 kHz) LF Biamp Mode: 600 W (2 hours, AES1984-2 method, 80 to 800 Hz) LF Triamp Mode: 400 W (x2) (2 hours, AES1984-2 method, 80 to 800 Hz)
HF: 300 W @ 16 ohms LF Biamp Mode: 1400 W @ 8 ohms LF Triamp Mode: 700 W @ 16 ohms (x2)
HF: 107.5 dB (single cabinet measured in free space) LF: 98 dB (single cabinet measured in free space. LF drivers connected in parallel)
Measured 1 W / 3.3' (1 m)
Continuous: HF: 127 dB LF: 127 dB Peak: HF: 133 dB LF: 133 dB
SPL @ 3.3' (1 m)
Nominal Coverage Angle
Horizontal: 140° Vertical: Dependent on number of elements used
Baltic birch plywood
Perforated, formed powder coated steel
2 x Neutrik Speakon NL8 in parallel
Integral, adjustable rigging system, vertical splay adjustable in 1° increments from 2° to 10° and 0°
10.75 x 27.5 x 20.25" (27.3 x 69.85 x 51.43 cm)
83 lb (37.7 kg)
The user manual for the QSC WL2102 WideLine-10 Line Array Speaker System WL2102-W-BK can be downloaded in .pdf
format if it did not come with your new pa speakers, although the seller is
required to supply one. It is also quite common that customers throw out
the user manual with the box, or put the CD away somewhere and then can’t find it.
That’s why we and other QSC users keep a unique electronic library
for QSC pa speakerss,
where you can use our link to download the user manual for the QSC WL2102 WideLine-10 Line Array Speaker System WL2102-W-BK.
The user manual lists all of the functions of the QSC WL2102 WideLine-10 Line Array Speaker System WL2102-W-BK,
all the basic and advanced features and tells you how to use the pa speakers.
The manual also provides troubleshooting for common problems. Even greater
detail is provided by the service manual, which is not typically shipped with the product,
but which can often be downloaded from QSC service.
If you want to help expand our database, you can upload a link to this website
to download a user manual or service manual, ideally in .pdf format. These pages
are created by you – users of the QSC WL2102 WideLine-10 Line Array Speaker System WL2102-W-BK. User manuals are also
available on the QSC website under Pro Audio - Live Sound - PA Speakers.
Question and answer discussion forum concerning user instructions and resolving problems with the QSC WL2102 WideLine-10 Line Array Speaker System WL2102-W-BK - no comments have been made yet - be the first to add a comment
looking for a user manual in English for this spotting scope the one I got is in a ll foreign languages...Lost quick release unit - Giottos Quick Release Plate MH642 Posted by: Frank Stacey 2019-09-14 16:22:23
Not sure if you are able to assist but I have a Giottos tripod with a quick release unit. It is the Bazooka Ik324. Unfortunately I have lost the QR plate and am having difficulty in getting a replacement. Your assisitance would be appreciated. If...