|
User manual for Ashly NXE1.54 Network Power Amplifier NXE1.54
- Manufacturer: Ashly
- Basic description and contents of package
- Product classification: Pro Audio - Installation Sound - 70-Volt Amplifiers
- Safety instructions
- Startup and operation of the 70-volt amplifiers
- Tips for setting up your Ashly
- Settings and expert assistance
- Contact Ashly service
- Troubleshooting
- Warranty information
|
We recommend checking out our discussion threads on the Ashly NXE1.54 Network Power Amplifier NXE1.54,
which address similar problems with connecting and setting up 70-Volt Amplifiers Ashly.
|
User manual for the Ashly NXE1.54 Network Power Amplifier NXE1.54
The user manual for the Ashly NXE1.54 Network Power Amplifier NXE1.54 provides
necessary instructions for the proper use of the product Pro Audio - Installation Sound - 70-Volt Amplifiers.
The NXE1.54 Network Power Amplifier from Ashly Audio is the networkable version of the nX amplifier. It comes with Ethernet control, serial data control, aux preamp outputs, instant standby mode, preset recall, fault condition logic outputs, and optional network audio and digital audio capability. All these are controlled using Ashly Audio's Protea software suite. This amplifier is designed to meet the most demanding live sound and fixed installation sound systems in stadiums, arenas, performance venues, worship spaces, and convention centers.
|
If you own a Ashly 70-volt amplifiers and have a user manual in electronic form,
you can upload it to this website using the link on the right side of the screen.
You can upload and download the manual for the Ashly NXE1.54 Network Power Amplifier NXE1.54 in the following formats:
- *.pdf, *.doc, *.txt, *.jpg - Other formats are unfortunately not supported.
|
Additional parameters of the Ashly NXE1.54 Network Power Amplifier NXE1.54:
| Maximum Output Power | Max Output Power Per Channel, EIAJ Test Standard
2 Ω: 1,500 W, 4 Ω: 1,500 W , 8 Ω: 1,250 W
Low Z output, Bridge Mode, 20Hz to 20kHz, 1%THD, All Channels Driven
4 Ω: 3,000 W
70 V, 100 V Output, All Channels Driven
70 V (per channel): 1,500 W
100 V (per channel): 1,250 W | | Power Draw | Total Power Draw All Channels Driven
Sleep Mode: <1 W
Standby Mode: 70 W
Idle (no signal): 100 W | | Current Draw | Current Draw 120VAC Mains (divide in half for 240V)
Sleep Mode: 0.1 A
Standby Mode: 1.30 A
Idle (no signal): 1.85 A
Maximum Current Draw All Channels Driven, Divide by 2 for 240VAC
Typical: 16.0 A | | Dissipation | Thermal Dissipation BTU/hr, All Channels Driven
Sleep Mode: <3.4
Standby Mode: 238
Idle (no signal): 340
Typical (1/8 max power): 1,700 | | Power Requirements | Power Requirements (@ 50/60Hz)
Nominal (Automatic Sensing SMPS)@ 50 Hz
Nominal (Automatic Sensing SMPS): 120 VAC
Operating Range: 70 to 135 VAC
Minimum Power-Up: 85 VAC
Power Requirements @ 60Hz
Nominal (Automatic Sensing SMPS): 240 VAC
Operating Range: 140 to 270 VAC
170 VAC | | Power Connector | Power Cable Connector: 20 A powerCON | | Input Source | Input Source Select Options (Protea DSP): Analog, Auto (Net, AES3, Analog) | | Limiter | Brick Wall Limiter (Protea DSP)
Threshold: -20 to +20 dBu
Ratio: Infinite
Attack: 0.2 to 50 ms/dB
Release: 5 to 1000 ms/dB | | Compressor | Threshold: -20 to +20 dBu
Ratio: 1.2:1 to infinite
Attack: 0.2 to 50 ms
Release: 5 to 1000 ms/dB
Detector: Peak / average
Attenuation Bus: 2 available
Metering: In, out, attenuation, graphical | | Control | Autoleveler Controls
Target Level: -40 to +20 dBu
Action: Gentle, normal, aggressive, user defined
Maximum Gain: 0 to +22 dB
Metering: Input, Gain, Attenuation
Ratio: 1.2:1 to 10:1
Threshold Below Target: -30 to 0 dB
Gain Increase/Decrease Rate: 5 to 1000 ms/dB
Hold Time: 0 to 6 s | | Noise | Ambient Noise Compensation: Output Only
Max Gain: -20 to +20 dB
Min/Base Gain: -40 to +20 dB
Gain Change Rate: 0.2 to 20 s/dB
Link Group: 16 available
ANC Input Channel: 1 to 2 or 1 to 4
Noise Threshold: -40 to +20 dBu
Program/Ambient Gain Ratio: 0.3:1 to 3:1
Metering: Input level, Attenuation, Average noise | | Ducking | Ducking: High/Low Priority, Trigger, Filibuster, Ducked Program
Trigger Threshold: -80 to +20 dBu
Ducking Release: 5 to 1000 ms / dB
Ducking Depth: 0 to -30 dB, -∞
Metering: Input | | Gate | Threshold: -80 to +20 dBu
Range: off, 100 to 0 dB
Attack: 0.2 to 50 ms/dB
Release: 5 to 1000 ms/dB
Metering: Key signal, Gate LED, graphical
Advanced Gate Controls
Key Frequency: 20 Hz to 20 kHz
Key Bandwidth: 0.016 to 3.995 octave | | Gain | Gain (with/without VCA): -50 to +12 dB, off, polarity invert
Digital VCA Groups: 4 available
Remote RD8C Gain: Enable per channel, 0 dB to -∞
WR-5 (neWR-5) Remote Gain: 0 to -50 dB, mute | | Band | 31-Band
Filter Type: Constant Q or proportional
Bandwidth: 0.499 to 0.25 oct
Parametric 2,4,6, or 10 Band
Frequency: 20 Hz to 20 kHz
Level: -30 to +15 dB
Q Value: 0.016 to 3.995 octave
Hi/Low Shelf 6/12 dB/oct
Frequency: 20 Hz to 20 kHz
Level: -15 to +15 dB
All Pass
Frequency: 20 Hz to 20 kHz
Variable Q HP/LP
Frequency: 20 Hz to 20 kHz
Q Value: 3.047 to 0.267
Notch/Bandpass
Frequency: 20 Hz to 20 kHz
Q Value: 92.436 to 0.267
Filters: 12
Filter Modes: Float, restricted, manual
Filter Type: Notch, parametric
Filter Frequency Range: 20 Hz to 20 kHz
Notch Filter: -∞
Parametric Filter: +15 to -30 dB
Filter Bandwidth: 0.016 to 3.995 octave
Detector Sensitivity: 5 levels
Float Time: 5 minutes to 24 hours
Bessel & Butterworth Filters: 12/18/24/48 dB/oct
Linkwitz-Riley Filter: 12/24/48 dB/oct
Frequency: Off, 20 Hz to 20 kHz
Speaker Delay: 0 to 21 ms
Delay: 0 to 682 ms
Speaker Delay: 0 to 10.6 ms
Delay: 0 to 341 ms | | Audio Metering | Range: -60 to +20 dBu
Increments: 1 dB
Signal Level: Off, -50 to +20 dBu
Sine Wave Frequency: 20 Hz to 12 kHz | | Matrix Type | Matrix Mixer
Gain (0.5dB increments): Off, -50 to +12 dB
Mute: Per channel
Auto-mixer Enabled: Per channel
Global Auto-mixer Response: 0.01 to 2 sec
Ducking LED: Per channel if enabled
Metering: Level, auto-mixer level | | Processor | Input A/D, Output D/A: 24-bit
DSP Processors: 32-bit floating point
Sample Rates: 48, 96 kHz
Propagation Delay @ 48kHz: 1.42 ms
Propagation Delay @ 96kHz: 0.71 ms | | Cooling | Continuously variable temperature controlled axial fan(s) | | Environmental | Non Condensing: 32 to 113⁰F ( 0 to 45⁰C) | | Dimensions (W x H x D) | 19.0 x 3.5 x 16.8" (483.0 x 89.0 x 428.0 mm) | | Weight | <28 lb (12.7 kg) | | Package Weight | 27.0 lb | | Box Dimensions (LxWxH) | 19.0 x 16.0 x 4.0" | |
The user manual for the Ashly NXE1.54 Network Power Amplifier NXE1.54 can be downloaded in .pdf
format if it did not come with your new 70-volt amplifiers, although the seller is
required to supply one. It is also quite common that customers throw out
the user manual with the box, or put the CD away somewhere and then can’t find it.
That’s why we and other Ashly users keep a unique electronic library
for Ashly 70-volt amplifierss,
where you can use our link to download the user manual for the Ashly NXE1.54 Network Power Amplifier NXE1.54.
The user manual lists all of the functions of the Ashly NXE1.54 Network Power Amplifier NXE1.54,
all the basic and advanced features and tells you how to use the 70-volt amplifiers.
The manual also provides troubleshooting for common problems. Even greater
detail is provided by the service manual, which is not typically shipped with the product,
but which can often be downloaded from Ashly service.
If you want to help expand our database, you can upload a link to this website
to download a user manual or service manual, ideally in .pdf format. These pages
are created by you – users of the Ashly NXE1.54 Network Power Amplifier NXE1.54. User manuals are also
available on the Ashly website under Pro Audio - Installation Sound - 70-Volt Amplifiers.
Question and answer discussion forum concerning user instructions and resolving problems with the Ashly NXE1.54 Network Power Amplifier NXE1.54 - no comments have been made yet - be the first to add a comment
Post new comment/question/response regarding the Ashly NXE1.54 Network Power Amplifier NXE1.54
|
|
|
|
|
