|
User manual for ETC Net3 N34G-4T Four-Port Gateway Rack-Mount Terminal 4260A1106
- Manufacturer: ETC
- Basic description and contents of package
- Product classification: Lighting & Studio - Lighting Accessories - DMX Devices
- Safety instructions
- Startup and operation of the dmx devices
- Tips for setting up your ETC
- Settings and expert assistance
- Contact ETC service
- Troubleshooting
- Warranty information
|
We recommend checking out our discussion threads on the ETC Net3 N34G-4T Four-Port Gateway Rack-Mount Terminal 4260A1106,
which address similar problems with connecting and setting up DMX Devices ETC.
|
User manual for the ETC Net3 N34G-4T Four-Port Gateway Rack-Mount Terminal 4260A1106
The user manual for the ETC Net3 N34G-4T Four-Port Gateway Rack-Mount Terminal 4260A1106 provides
necessary instructions for the proper use of the product Lighting & Studio - Lighting Accessories - DMX Devices.
The ETC Net3 N34G-4T Four-Port Gateway Rack-Mount Terminal Bundle provides connection for up to four DMX lines and is designed for customers who do not need typical DMX connectors for lighting control of their permanently installed systems. The bare wire is mounted into the terminal ports using the provided terminal prep kit. Included in the bundle are the Gateway unit with 4 terminal strip modules, a rack mount and a universal power supply. By default, the bundle will come with terminal connectors for DMX wire and the appropriate preparation kit. If you are connecting to Category 5 wire for DMX, request the DMX termination preparation kit with IDC connectors from ETC when purchasing this bundle.
The Gateway is a configurable gate for essential DMX, sACN and Remote Device Management data to be distributed throughout your entire network, ensuring not just basic control of your lights, but also peace of mind that all components are functioning as designed. Using bidirectional Ethernet communication the health of the data signal can be monitored. RDM is a protocol enhancement to DMX512 that allows bi-directional communication between a lighting or system controller and attached RDM compliant devices over a standard DMX line. This protocol will allow configuration, status monitoring, and management of these devices in such a way that does not disturb the normal operation of standard DMX512 devices that do not recognize the RDM protocol. The Gateway unit's LCD readout provides information on DMX terminal port, RDM and network configurations. The modular design of the Net3 Gateway enables the user to tailor the number and type of inputs and outputs to suit a particular venue or location.
The terminal strip module comes with ETC's standard DMX termination preparation kit which includes instructions and all parts required for installation. This bundle provides the user with the ability to mount the Gateway into a standard 19" control rack slot. Two Gateways can be mounted side-by-side if required. The Gateway is fabricated from 16-gauge cold-rolled steel and finished in fine-texture, scratch resistant black powder coat.
|
If you own a ETC dmx devices and have a user manual in electronic form,
you can upload it to this website using the link on the right side of the screen.
You can upload and download the manual for the ETC Net3 N34G-4T Four-Port Gateway Rack-Mount Terminal 4260A1106 in the following formats:
- *.pdf, *.doc, *.txt, *.jpg - Other formats are unfortunately not supported.
|
Additional parameters of the ETC Net3 N34G-4T Four-Port Gateway Rack-Mount Terminal 4260A1106:
| Power | IEEE802.3af Power over Ethernet
8-28 VDC external power supply
Maximum power consumption > 5 watts | | Connectors | 4 x 8-Pin terminal connectors
1 x RJ45 Ethernet DMX connector
Terminal strip connector
Fully optically-isolated input from the gateway electronics
Integrated DMX/RDM termination | | Environmental | Ambient operating temperature: 32° to 104°F (0° to 40°C)
Operating humidity: 5-95% non-condensing
CE compliant and ETL listed | | Data Signal | Maximum delay time from input to output not greater than one packet time - 22mS
Selectable DMX refresh rate with a maximum < 40 Hz | | Dimensions | Gateway: 8.5 x 8.2 x 1.7" (21.5 x 21.0 x 4.5 cm) | | Weight | Gateway, rack mount and power supply: 6 lb (2.7 kg) | |
The user manual for the ETC Net3 N34G-4T Four-Port Gateway Rack-Mount Terminal 4260A1106 can be downloaded in .pdf
format if it did not come with your new dmx devices, although the seller is
required to supply one. It is also quite common that customers throw out
the user manual with the box, or put the CD away somewhere and then can’t find it.
That’s why we and other ETC users keep a unique electronic library
for ETC dmx devicess,
where you can use our link to download the user manual for the ETC Net3 N34G-4T Four-Port Gateway Rack-Mount Terminal 4260A1106.
The user manual lists all of the functions of the ETC Net3 N34G-4T Four-Port Gateway Rack-Mount Terminal 4260A1106,
all the basic and advanced features and tells you how to use the dmx devices.
The manual also provides troubleshooting for common problems. Even greater
detail is provided by the service manual, which is not typically shipped with the product,
but which can often be downloaded from ETC service.
If you want to help expand our database, you can upload a link to this website
to download a user manual or service manual, ideally in .pdf format. These pages
are created by you – users of the ETC Net3 N34G-4T Four-Port Gateway Rack-Mount Terminal 4260A1106. User manuals are also
available on the ETC website under Lighting & Studio - Lighting Accessories - DMX Devices.
Question and answer discussion forum concerning user instructions and resolving problems with the ETC Net3 N34G-4T Four-Port Gateway Rack-Mount Terminal 4260A1106 - no comments have been made yet - be the first to add a comment
Post new comment/question/response regarding the ETC Net3 N34G-4T Four-Port Gateway Rack-Mount Terminal 4260A1106
|
|
|
|
|
