User manual Lectrosonics DNT16i - 16 Analog Input Dante Network DNT16I
Operating instructions and pdf manual for use - Lectrosonics DNT16i - 16 Analog Input Dante Network DNT16I User manual, User manual Lectrosonics DNT16i - 16 Analog Input Dante Network DNT16I, Lectrosonics, DNT16i, 16, Analog, Input, Dante, Network,
User manual for Lectrosonics DNT16i - 16 Analog Input Dante Network DNT16I
Manufacturer: Lectrosonics
Basic description and contents of package
Product classification: Pro Audio - Installation Sound - Networked Audio Systems
Safety instructions
Startup and operation of the networked audio systems
Tips for setting up your Lectrosonics
Settings and expert assistance
Contact Lectrosonics service
Troubleshooting
Warranty information
We recommend checking out our discussion threads on the Lectrosonics DNT16i - 16 Analog Input Dante Network DNT16I,
which address similar problems with connecting and setting up Networked Audio Systems Lectrosonics.
User manual for the Lectrosonics DNT16i - 16 Analog Input Dante Network DNT16I
The user manual for the Lectrosonics DNT16i - 16 Analog Input Dante Network DNT16I provides
necessary instructions for the proper use of the product Pro Audio - Installation Sound - Networked Audio Systems.
The DNT16i from Lectrosonics is a processor that provides inputs into a Dante network from analog and digital signals. Each input provides extensive signal processing and routing to any one or all of forty-eight automatic mixers operating at the cross points of an internal digital matrix in the processor.
The outputs of the matrix can be assigned to a Dante transmit channel and/or routed back to an input to be further mixed with another input or matrix mix.
If you own a Lectrosonics networked audio systems and have a user manual in electronic form,
you can upload it to this website using the link on the right side of the screen.
You can upload and download the manual for the Lectrosonics DNT16i - 16 Analog Input Dante Network DNT16I in the following formats:
*.pdf, *.doc, *.txt, *.jpg - Other formats are unfortunately not supported.
Additional parameters of the Lectrosonics DNT16i - 16 Analog Input Dante Network DNT16I:
Specifications
Audio Inputs
(Balanced microphone/line level inputs with digitally programmable gain may be configured as unbalanced inputs) Audio Input Channels Analog: 16 mic/line level Digital: 16 Dante channels Gain Analog: 0 dB to 56 dB, programmable in 8 dB steps (the analog gain is automatically set by selecting the input gain) Digital (Dante): -70 dB to +20 dB Performance Impedance: 8kΩ differential mode, 2kΩ common mode Maximum Analog Input Level: 20 dBu Dynamic Range: 102 dB EIN: -127 dBu (20 Hz to 20 kHz, unweighted) THD + Noise: 0.01% A-D Sampling Rate: 48 kHz, fixed
Audio Outputs
Digital: 32 outputs delivered to the Dante network
Dante Interface
Provides dual RJ-45 connectors on the rear panel and an Ethernet switch built into the processor Supported Sampling Rate: 48 kHz Data Rate LED: 100 Mbps/1 Gbps Activity LED: Blinks when active Modes of Operation Switched mode using either connector Redundant mode with primary and secondary networks using both connectors
Network Connectivity
Dante interface and Ethernet control can be connected to the same network
Filters
All filters have zero processing delay Tone Control Stages: 4 per input channel ADFE: 8 per input channel, configurable as static or dynamic
Internal Signal Generator
Swept Sine Modes: Single sweep, continuous sweep Waveforms: Sawtooth (up or down), triangle Sweep Rate: Linear, logarithmic Parameters: Start freq, stop freq, level (dBu), sweep time (sec) White Noise Parameter: Level (dBu) Pink Noise Parameter: Level (dBu) Tone (Sine Wave) Parameters: Level (dBu), frequency
Soft knee with RMS level detector eliminates need for separate attack and delay settings 0.1 ms increments 1 second maximum Continuously adjustable ratio
The user manual for the Lectrosonics DNT16i - 16 Analog Input Dante Network DNT16I can be downloaded in .pdf
format if it did not come with your new networked audio systems, although the seller is
required to supply one. It is also quite common that customers throw out
the user manual with the box, or put the CD away somewhere and then can’t find it.
That’s why we and other Lectrosonics users keep a unique electronic library
for Lectrosonics networked audio systemss,
where you can use our link to download the user manual for the Lectrosonics DNT16i - 16 Analog Input Dante Network DNT16I.
The user manual lists all of the functions of the Lectrosonics DNT16i - 16 Analog Input Dante Network DNT16I,
all the basic and advanced features and tells you how to use the networked audio systems.
The manual also provides troubleshooting for common problems. Even greater
detail is provided by the service manual, which is not typically shipped with the product,
but which can often be downloaded from Lectrosonics service.
If you want to help expand our database, you can upload a link to this website
to download a user manual or service manual, ideally in .pdf format. These pages
are created by you – users of the Lectrosonics DNT16i - 16 Analog Input Dante Network DNT16I. User manuals are also
available on the Lectrosonics website under Pro Audio - Installation Sound - Networked Audio Systems.
Question and answer discussion forum concerning user instructions and resolving problems with the Lectrosonics DNT16i - 16 Analog Input Dante Network DNT16I - no comments have been made yet - be the first to add a comment