PDF-MANUALS.com | User manual here!
User manual

User manual Ashly nXp Series NXP8004 4-Channel 800W Power Amplifier NXP8004

Operating instructions and pdf manual for use - Ashly nXp Series NXP8004 4-Channel 800W Power Amplifier NXP8004 User manual, User manual Ashly nXp Series NXP8004 4-Channel 800W Power Amplifier NXP8004, Ashly, nXp, Series, NXP8004, 4-Channel, 800W,

User manual for Ashly nXp Series NXP8004 4-Channel 800W Power Amplifier NXP8004

Ashly nXp Series NXP8004 4-Channel 800W Power Amplifier NXP8004
  • Manufacturer: Ashly
  • Basic description and contents of package
  • Product classification: Pro Audio - Live Sound - Power Amplifiers
  • Safety instructions
  • Startup and operation of the power amplifiers
  • Tips for setting up your Ashly
  • Settings and expert assistance
  • Contact Ashly service
  • Troubleshooting
  • Warranty information
We recommend checking out our discussion threads on the Ashly nXp Series NXP8004 4-Channel 800W Power Amplifier NXP8004, which address similar problems with connecting and setting up Power Amplifiers Ashly.


User manual for the Ashly nXp Series NXP8004 4-Channel 800W Power Amplifier NXP8004

The user manual for the Ashly nXp Series NXP8004 4-Channel 800W Power Amplifier NXP8004 provides necessary instructions for the proper use of the product Pro Audio - Live Sound - Power Amplifiers.

The nXp Series NXP8004 4-Channel 800W Power Amplifier with Programmable Outputs & Protea Software Suite from Ashly is a Class-D switching amplifier combined with a switch mode power supply. This amplifier meets the requirements of demanding live sound and fixed installation sound systems in stadiums, arenas, performance venues, worship spaces, and convention centers.
If you own a Ashly power amplifiers and have a user manual in electronic form, you can upload it to this website using the link on the right side of the screen.

You can upload and download the manual for the Ashly nXp Series NXP8004 4-Channel 800W Power Amplifier NXP8004 in the following formats:
  • *.pdf, *.doc, *.txt, *.jpg - Other formats are unfortunately not supported.
Additional parameters of the Ashly nXp Series NXP8004 4-Channel 800W Power Amplifier NXP8004:

Go To

Processor
Input Source Protea DSP Options: Analog, auto (net, AES3, analog)

All DSP functions can be linked to 1 of 16 link groups
Limiter Brick Wall Limiter: Threshold: -20 to 20 dBu
Ratio: Infinite
Attack: 0.2 to 50 ms/dB
Release: 5 to 1000 ms/dB
Control Advanced Gate Controls
Key Engage Enable
Key Frequency: 20 Hz to 20 kHz
Key Bandwidth: 0.016 to 3.995 octave
Gain Gain (with / without VCA): -50 to 12 dB, off, polarity invert
Digital VCA Groups: 4 available
Remote RD8C Gain: Enable per channel, 0 dB to -∞
WR-5 (neWR-5) Remote Gain: 0 to -50 dB, mute
EQ Type For 31-Band
Filter Type: Constant Q or proportional
Bandwidth: 0.499 octave to 0.25 octave

For Parametric 2,4,6, or 10 Band
Frequency: 20 to 20 kHz
Level: -30 to 15 dB
Q Value: 0.016 to 3.995 octave

For Hi / Low Shelf 6 / 12 dB/octave
Frequency: 20 Hz to 20 kHz
Level: -15 to 15 dB

For All Pass
Frequency: 20 Hz to 20 kHz

For Variable Q HP / LP
Frequency: 20 Hz to 20 kHz
Q Value: 3.047 to 0.267

For Notch / Bandpass
Frequency: 20 Hz to 20 kHz
Q Value: 92.436 to 0.267

Feedback Suppressor (48 kHz Sampling Rate)
12 x filters
In/Out per filter
Lock (per filter) and global lock
Filter Modes: Float, restricted, manual
Filter Type: Notch, parametric
Filter Frequency Range: 20 Hz to 20 kHz
Notch Filter: -∞
Parametric Filter: 15 to -30 dB
Filter Bandwidth 0.016 to 3.995 Octave
Detector Sensitivity: 5 levels
Float Time 5 minutes to 24 hours
Filter FIR Filter: .fir or .csv file types
Crossover 2-Way, 3-Way, 4-Way Crossover & High Pass / Low Pass Filters
Bessel & Butterworth Filters: 12 / 18 / 24 / 48 dB/octave
Linkwitz-Riley Filter: 12 / 24 / 48 dB / octave
Frequency: Off, 20 Hz to 20 kHz
Delay Sampling Rate: At 48 kHz (Input Time, Distance & Temperature)
Speaker Delay: 0 to 21 ms
Delay: 0 to 682 ms

At 96 kHz (Input Time, Distance & Temperature)
Speaker Delay: 0 to 10.6 ms
Delay: 0 to 341 ms
Audio Metering Range: -60 to 20 dBu
Increments: 1 dB
Peak Hold Indicator
Signal Generator Pink Noise, White Noise, Sine Wave
Signal Level: Off, -50 to 20 dBu
Sine Wave Frequency: 20 Hz to 12 kHz
Processor Input A/D, Output D/A: 24-bit
DSP Processors: 32-bit floating point
Sample Rates: 48 kHz, 96 kHz
Propagation Delay @ 48 kHz: 1.42 ms
Propagation Delay @ 96 kHz: 0.71 ms
Mixer Gain (0.5 dB Increments): Off, -50 to 12dB
Mute: Per channel
Auto-mixer Enabled: Per channel
Global Auto-mixer Response: 0.01 to 2 sec
Enable Ducking at Mixer
Ducking LED: Per channel if enabled
Metering: Level, auto-mixer level
Compressor
Threshold -20 to 20 dBu
Ratio 1.2:1 to infinite
Attack 0.2 to 50 ms
Release 5 to 1000 ms/dB
Detectors Peak / average
Attenuation 2 available
Metering In, out, attenuation, graphical
Auto Leveler Controls
Level Target Level: -40 to 20 dBu
Action Type Gentle, normal, aggressive, user defined
Maximum Gain 0 to 22 dB
Metering Input, gain, attenuation
Ratio 1.2:1 to 10:1
Threshold -30 to 0 dB
Gain 5 to 1000 ms/dB
Hold 0 to 6 seconds
Ambient Noise Compensation
Output Gain Maximum: -20 to 20 dB
Minimum Base: -40 to 20 dB
Gain Adjustment Range 0.2 to 20 s/dB
Groups Link Groups: 16 available
Input Channels ANC: 1 to 4
Threshold Range Output Noise: -40 to 20 dBu
Ratio Program/Ambient Gain: 0.3:1 to 3:1
Metering Input level, attenuation, average noise
Ducking Trigger Threshold: -80 to 20 dBu
Ducking Release: 5 to 1000 ms/dB
Ducking Depth: 0 to -30 dB, -∞
Enable Ducking at Matrix Mixer
Metering: Input
Gate
Threshold -80 to 20 dBu
Range Off, 100 to 0 dB
Attack 0.2 to 50 ms/dB
Release 5 to 1000 ms/dB
Metering Key signal, gate LED, graphical
Power Requirements
Power At 50 Hz
Nominal (Automatic Sensing SMPS): 120 VAC
Operating Range: 70 to 135 VAC
Minimum Power-Up: 85 VAC

At 60 Hz
Nominal (Automatic Sensing SMPS): 240 VAC
Operating Range: 140 to 270 VAC
Minimum Power-Up: 170 VAC
Connector Power Cable Connector: 20 A powerCON
Maximum Output Power Per Channel, Low-Z Output, All Channels Driven
2/4/8 Ω: 800 W
Output Low Z Output, Bridge Mode, All Channels Driven: 1600 W (4/8 Ω)
70 V, 100 V Output, All Channels Driven: 800 W (70/100 V (per channel)
Power Draw Sleep Mode: < 1 W
Standby Mode: 40 W
Idle (No Signal): 70 W

All Channels Driven
Current Draw For 120 VAC
Sleep Mode: 0.1 A
Standby Mode: 0.70 A
Idle (No Signal): 1.30 A

For 240 VAC
Sleep Mode: 0.05 A
Standby Mode: 0.35 A
Idle (No Signal): 0.65 A

Maximum, All Channels Driven, Typical Input
1/8 Max Power @ 2 Ω): 8.8 A for 120 VAC, 4.4 A for 240 VAC

Dissipation Thermal Dissipation: Sleep Mode: <3.4 BTU/hr
Standby Mode: 136 BTU/hr
Idle (no signal): 238 BTU/hr
Typical (1 / 8 Max Power @ 2 Ω): 970 BTU/hr

All Channels Driven
LED Indicators Front Panel LED Indicators
White: Power Switch: On, off, standby (flashing)

Red LED:
Clip / Mute Per Channel: Clip @ 1 dB below full output / mute
Protect: On (fault condition or shut down), Off

Green LED:
Signal Per Channel: -18 dBu, below rated output
Bridge Per Channel Pair: On, off
Com: On, for Ethernet data or device ID
Current Per Channel: Proportional to output

Yellow LED:
Temperature Per Channel: On dim at 90% maximum operating temperature, full bright + protect at 100%
Sleep: On, amplifier is asleep from audio inactivity
Disable: On, power switch & front panel attenuators are disabled
General
Voltage Gain Selectable at 26, 32, or 38 dB, and 1.4 V

0 dBu = 0.775 VRMS
Damping Factor >250 (8 Ω load <1 kHz)
Filter Input High Pass Filter: 80 Hz 2nd order
Distortion <0.5% SMPTE, typical
<0.5% THD-N, typical (8 Ω, 10 dB below rated power, 20 Hz to 20 kHz)
Channel Separation -75 dB (dB from full output, 1 kHz)
Signal / Noise 20 Hz to 20 kHz, un-weighted: >108 dB
Frequency Response 20 Hz to 20 kHz, ±0.05 dB
Connector Balanced Input Connector: Euroblock 3.5 mm, 1/4" TRS and XLR combo jack
Input Impedance 10 kΩ
Maximum Input Level 21 dBu
Speaker Output Connector: Neutrik & speakON
Network Control Network: Compatible with standard 100 MB Ethernet
AUX Outputs Connector: Balanced Euroblock 3.5 mm
Maximum Output Level: 21 dBu
Contact Closure Remote Standby: Euroblock 3.5 mm, close contact to GND for standby mode
Preset Recall: Euroblock 3.5 mm, close contact to GND for preset 1-4 recall
Data Data Connection: Euroblock 3.5 mm - Gnd, 18 V, in, out
Outputs Fault Condition Logic Outputs: 4 x 3.5 mm Euroblock
Level Control Remote DC: 4 x 3.5 mm Euroblock - Gnd, CV, V+ per input
Attenuation Front panel, software, offset link group, and remote per channel
Fully off = mute
Protection Circuits Inrush current limitation, temperature monitoring, output over-power protection, and mains fuses
Cooling Continuously variable temperature controlled axial fans
Environmental Non-condensing 32 to 113°F (0 to 45°C)
Dimensions (W x H x D) 19.0 x 3.5 x 16.8" (48.3 x 8.9 x 42.8 cm)
Weight 32.4 lb (14.8 kg)
Packaging Info
Package Weight 32.5 lb
The user manual for the Ashly nXp Series NXP8004 4-Channel 800W Power Amplifier NXP8004 can be downloaded in .pdf format if it did not come with your new power amplifiers, although the seller is required to supply one. It is also quite common that customers throw out the user manual with the box, or put the CD away somewhere and then can’t find it. That’s why we and other Ashly users keep a unique electronic library for Ashly power amplifierss, where you can use our link to download the user manual for the Ashly nXp Series NXP8004 4-Channel 800W Power Amplifier NXP8004.

The user manual lists all of the functions of the Ashly nXp Series NXP8004 4-Channel 800W Power Amplifier NXP8004, all the basic and advanced features and tells you how to use the power amplifiers. The manual also provides troubleshooting for common problems. Even greater detail is provided by the service manual, which is not typically shipped with the product, but which can often be downloaded from Ashly service.

If you want to help expand our database, you can upload a link to this website to download a user manual or service manual, ideally in .pdf format. These pages are created by you – users of the Ashly nXp Series NXP8004 4-Channel 800W Power Amplifier NXP8004. User manuals are also available on the Ashly website under Pro Audio - Live Sound - Power Amplifiers.


Discussion Question and answer discussion forum concerning user instructions and resolving problems with the Ashly nXp Series NXP8004 4-Channel 800W Power Amplifier NXP8004 - no comments have been made yet - be the first to add a comment

Post new comment/question/response regarding the Ashly nXp Series NXP8004 4-Channel 800W Power Amplifier NXP8004

Fields marked with * must be filled out.
Your name *:
E-mail :
Subject *:
Message text *:
Enter the code *:
(spam block)		 "manual"
If you would like to receive a response to your comment, don’t forget to include your e-mail address. Your e-mail will not be displayed or otherwise used in any way.

 

Can't find what you're looking for? Try Google Search!

Current discussions
Most recently discussed products:

Wiring/configure 501n-3 for rear view switch - Rear View Safety RVS-501N 3-Channel Multiplexer RVS-501N
Posted by: Ron Diller
2025-05-06 23:25:57

Hello,I replaced the rv radio, which controls back,and turn signal cameras. How can I wire it to have the backup camera on all the time as a rear view mirror function, except when blinkers are on. Thanks! ...
Wiring/configure 501n-3 for rear view switch - Rear View Safety RVS-501N 3-Channel Multiplexer RVS-501N
Posted by: Ron Diller
2025-05-06 23:25:03

Hello,I replaced the rv radio, which controls back,and turn signal cameras. How can I wire it to have the backup camera on all the time as a rear view mirror function, except when blinkers are on. Thanks! ...
sony alpha 7II - Sony Alpha a7 II Mirrorless Digital Camera with 28-70mm Lens
Posted by: Clabue
2025-05-06 13:13:48

Alpha 7 II - Black + Sony FE 28-70mm f/3.5-5.6 OSS f/3.5-5.6 Where can I find a manual. It didn't come with the camera I just purchased online. Thank you....
FBA-Pioneer BDR-XU03 - Pioneer BDR-XU03 USB 3.0 BD/DVD/CD Burner BDR-XU03
Posted by: Mark Visel
2025-05-05 20:51:42

Sorry, but I am having one hell of a time finding this manual. Bought thru Amazon and am getting no where with finding manual. Can someone help....
SRD-92B setting - Fujinon SRD92B Zoom Rate Demand SRD-92B
Posted by: Matthew Allen
2025-05-04 14:10:30

How can we make the speed adjustment control slower...

Uploaded instruction manuals
Upload a link to an instruction manual for a depicted product here:

Link format "http://www.link2manual.com/manual.pdf"

Enter the code: "manual"




PDF-MANUALS.com - Community administered database of instructions for use and PDF User manual
sitemap.txt alx