User manual Radial Engineering Bassbone OD 2-Channel Bass Preamp R800 7072
Operating instructions and pdf manual for use - Radial Engineering Bassbone OD 2-Channel Bass Preamp R800 7072 User manual, User manual Radial Engineering Bassbone OD 2-Channel Bass Preamp R800 7072, Radial, Engineering, Bassbone, OD, 2-Channel, Ba
User manual for Radial Engineering Bassbone OD 2-Channel Bass Preamp R800 7072
Manufacturer: Radial Engineering
Basic description and contents of package
Product classification: Pro Audio - Musical Instruments - Effects Pedals
Safety instructions
Startup and operation of the effects pedals
Tips for setting up your Radial Engineering
Settings and expert assistance
Contact Radial Engineering service
Troubleshooting
Warranty information
Price: 350 USD
We recommend checking out our discussion threads on the Radial Engineering Bassbone OD 2-Channel Bass Preamp R800 7072,
which address similar problems with connecting and setting up Effects Pedals Radial Engineering.
User manual for the Radial Engineering Bassbone OD 2-Channel Bass Preamp R800 7072
The user manual for the Radial Engineering Bassbone OD 2-Channel Bass Preamp R800 7072 provides
necessary instructions for the proper use of the product Pro Audio - Musical Instruments - Effects Pedals.
The Bassbone OD from Radial Engineering is a bass preamp with two instrument input channels, each of which is fully equipped with a level control, a passive-interactive EQ, and a low-frequency filter to help eliminate resonance. Channel-A is equipped with a PZB booster switch that increases the sensitivity and load to 10 MOhms to optimize it for use with piezo transducers as commonly used on upright bass. Channel-B is equipped with Drag Control load correction to optimize the tone and feel when using a passive instrument such as a vintage Fender bass. Toggling between channels is done using a footswitch. When using a dual pickup system, both channels may be mixed together by depressing the blend switch. Outputs include a 1/4" instrument level output to feed the artist's on-stage amplifier, plus a balanced low-Z Radial DI box output to feed the PA system. The XLR output can be assigned pre or post effects to suit your preference. A separately buffered tuner output works with the mute footswitch for quiet on-stage tuning.
If you use effects, both input channels can share the same pedals by connecting via the built-in send & receive effects loop. This is augmented with an on-board bass overdrive with control over the drive level and tone. The OD footswitch may be assigned to the loop, overdrive, or both. The Bassbone also features a built-in headphone amp with 3.5mm output.
If you own a Radial Engineering effects pedals and have a user manual in electronic form,
you can upload it to this website using the link on the right side of the screen.
You can upload and download the manual for the Radial Engineering Bassbone OD 2-Channel Bass Preamp R800 7072 in the following formats:
*.pdf, *.doc, *.txt, *.jpg - Other formats are unfortunately not supported.
Additional parameters of the Radial Engineering Bassbone OD 2-Channel Bass Preamp R800 7072:
Specifications
Audio Circuit Type
Discrete class-A FET input with low noise ICs
Frequency Response
20 Hz - 18 kHz
Total Harmonic Distortion
0.05% @ -15 dBu
Intermodulation Distortion
0.2% @ -20 dBu
Dynamic Range
85 dB
Input Impedance
Input A: 220 kOhms / 10 MOhms Input B: Variable from 22 kOhms to 1.8 MOhms
Output Impedance
300 ohms at XLR
Maximum Input
+7 dBu
Gain
Unity gain device Boost Drive: 0 to 25 dB PZB Boost: +10 dB on channel A
Output Clip Level
+10 dBu at XLR
Noise Floor
-100 dB
Equivalent Input Noise
-92 dBu at XLR
Audio Connections
1/4" Output High-Z instrument-level 3.5 mm output Headphone, mono with volume control XLR output, balanced mic level, AES standard (pin-2 hot)
Controls
2 x Gain 2 x Low 2 x Mid 2 x High 1 x Drive 1 x Mix 1 x Tone in OD 1 x Drag
Switches
1 x PZB 1 x Blend 1 x FX 180 1 x XLR G/L & 180 1 x LOOP Mode 1 x EFX Mode 2 x HPF 2 x Mid Frequency
Low-Cut Filter
Flat, 80 Hz and 150 Hz
Filter Type (Slope)
6 dB / octave
Merge Function
Recessed Blend switch mixes ch-1 & ch-2 together
XLR Configuration
Pin 1 Ground Pin 2 + Pin 3 -
Ground Lift
Lifts pin-1 on the XLR
Power
+15 VDC / 400 mA (adapter included)
Construction
14-gauge steel
Finish
Powder-coat
Operating Conditions
Humidity: Dry locations Temperature: 41 to 104°F (5 to 40°C)
Dimensions
8.0 x 4.2 x 2.0" (20.3 x 10.7 x 4.8 cm)
Weight
2.6 lb (1.2 kg)
The user manual for the Radial Engineering Bassbone OD 2-Channel Bass Preamp R800 7072 can be downloaded in .pdf
format if it did not come with your new effects pedals, although the seller is
required to supply one. It is also quite common that customers throw out
the user manual with the box, or put the CD away somewhere and then can’t find it.
That’s why we and other Radial Engineering users keep a unique electronic library
for Radial Engineering effects pedalss,
where you can use our link to download the user manual for the Radial Engineering Bassbone OD 2-Channel Bass Preamp R800 7072.
The user manual lists all of the functions of the Radial Engineering Bassbone OD 2-Channel Bass Preamp R800 7072,
all the basic and advanced features and tells you how to use the effects pedals.
The manual also provides troubleshooting for common problems. Even greater
detail is provided by the service manual, which is not typically shipped with the product,
but which can often be downloaded from Radial Engineering service.
If you want to help expand our database, you can upload a link to this website
to download a user manual or service manual, ideally in .pdf format. These pages
are created by you – users of the Radial Engineering Bassbone OD 2-Channel Bass Preamp R800 7072. User manuals are also
available on the Radial Engineering website under Pro Audio - Musical Instruments - Effects Pedals.
Question and answer discussion forum concerning user instructions and resolving problems with the Radial Engineering Bassbone OD 2-Channel Bass Preamp R800 7072 - no comments have been made yet - be the first to add a comment
Why is the blue light (wireless symbol)...what is it on...its a blue light. I have had these for years and have never had that light come on and it is not allowing me to print! What do I do to turn it off? ...K&M manual - K&M 200 Telescoping Microphone Stand (Black) 20000-500-55 Posted by: jpdaval69 2024-09-10 00:50:11
I need the service manual/schematic of Universal Audio Solo/610 Serial number: 2310 MfgDt: 0607.
I hope you have it and I'm willing to be charged for it.
Best Regards....True Dock not recognizing hard drives - Kingwin True Dock Super-Speed USB 3.0 to TD-2535U3 Posted by: bf1955 2024-08-22 15:34:26
True Dock is not recognizing HDD, the HDD light does not come on, even though the power light does come one....